Floor Coating
CLEANPOXY SELF LEVELER MILD
- usage
- Interior dust-proofing floor primer for concrete floors
Cleanpoxy Self Leveler Mild is an epoxy self leveler which is designed for odorless application by using low odor raw materials. This paint is a non-solvent-based epoxy paint based on the epoxy-modified amine resin. It has a strong dry film and is excellent in adhesion, appearance, durability and chemical resistance. In particular, it is a non-solvent type epoxy paint that is suitable as a concrete floor paint because a thick coating is possible by one coat, and the smoothness of coating is good.
specification
- Paint type
- Modified epoxy / Modified amine (2-Component)
- Drying time
-
Drying time Category 5℃ 20℃ 30℃ Set-to-touch 10 hours 5 hours 3 hours Dry-through 48 hours 24 hours 18 hours Over-coat (Min.) 72 hours 48 hours 24 hours Over-coat (Max.) 9 days 4 days 3 days Pot life 60 minutes 30 minutes 20 minutes - Thinner
- Not Applicable
- Specific gravity
- Approx. 1.50 (Green)
- Dilution ratio
- ▷No dilutio
- Theoretical Coverage
- 1.5 ㎏/㎡ (Based on 1㎜), 3.0 ㎏/㎡ (Based on 2㎜), 4.5 ㎏/㎡ (Based on 3㎜)
- Solid volume ratio
- 96±3 %
- Color
- Green, gray, other ordered colors
- Thickness of dried film
- According to General Estimate of Quantities
- Mixing ratio
- Base(A)/hardener(B)=5/1 (Weight ratio)
- Gloss
- Glossy
- Shelf life
- 12 months
- Packaging unit
- 24 ㎏ [Base(20㎏), Hardener(4㎏)]
how to use
- Surface treatment
- 1. Cure concrete for at least 28 days at a temperature of 21℃ and a relative humidity of 50%.
2. Completely remove the oil, moisture, sand, dust, laitance and other foreign matter from the surface and maintain surface smoothness. - Coating method
- 1. Reinforce cracks, crevices, and joints between walls and floors with an epoxy putty after primer.
2. Add the hardener to the base and use after evenly mixing for 3-5 minutes with a power stirrer.
3. Apply smoothly using sawtooth scraper, rubber scraper, pitchfork, square towel, etc.
4. In order to prevent air bubbles on the lining surface, there should be no missing area on the undercoating, and it is effective if it is applied by dividing the lining into primary scrapping and secondary main coating.
▷Primer : CLEANPOXY PRIMER, CLEANPOXY DNY-200, CLEANPOX DNY-200E, CLEANPOX(W) PRIMER
▷Self Leveler : CLEANPOXY SELF LEVELER MILD
▷Top coat : CLEANPOXY 3100, CLEANPOXY COATING PLUS(if necessary)
▷Putty : NORUSEAL #6600, CLEANPOXY(LO) PUTTY(if necessary) - Coating conditions
- 1. Atmosphere Temperature: 5~35℃, Surface Temperature: 40℃ or below, Relative Humidity: 80% or less, Moisture content in the concrete: 6% or less
2. Please note that due to the nature of epoxy paint, discoloration and chalking may occur if exposed to the outdoor environment.
3. The use of a thinner more than the recommended amount causes further delay in drying, decline in hardness, whitening, skid marks, color separation, etc.
Above pot life and follow-up coating time have been measured under laboratory conditions and may vary depending on the construction site.
The film that has passed the maximum follow-up coating time may have adhesion failure. Please apply after checking the proper surface treatment and adhesion.